1. Device Help
  2. Installation Partner resources
  3. Reveal Hardware Installer
  4. Set up a camera in RHI

Install and set up an AI Dashcam with Reveal Hardware Installer app

This is a printed page that might be out of date. To read the most up-to-date help content, visit https://device-help.verizonconnect.com.

This article explains how to install an AI Dashcam using the Reveal Hardware Installer app.

If you already have a Road-facing camera and wish to upgrade to a dual-facing camera, you should instead use: Technician guide: Dual-Facing AI Dashcam using Reveal Hardware Installer app.

Note

A VTU must be installed in the vehicle before you can add an AI Dashcam.

  1. Navigate to the Work Ticket for the Install.

    RHI_Dashcam_Work_Ticket.png

  2. Input the Camera ESN by using the ESN Scan button. Alternatively, you can input the camera ESN manually by typing it in.

    RHI_Dashcam_Enter_ESN.png

  3. Select the task Installation - Road Facing or Dual Camera.

    RHI_Dashcam_Select_Task.png
  4. Tap Next.

  5. Identify the VTU to pair the camera with by scanning/entering the VIN, or by entering the license plate or ESN (for VTU), IMEI (for VDD).

    RHI_CP2_Identify_Device.png

  6. Toggle between search options by selecting Change search method.

    RHI_Dashcam_Change_Method.png

  7. Tap on the result once it has been found.

    RHI_Daschcam_Identify_Vehicle.png

  8. You’ll be brought to the Before you begin page. First time users should review the instructions in their entirety.

    RHI_Dashcam_Installation_Guide.png
  9. When ready to proceed with the installation, select Start installation.

  10. Connect to power, turn on ignition and wait 5 minutes for boot up.

    RHI_Dashcam_Connect_to_Power.png

  11. Remove the camera side panel.

    RHI_Dashcam_Remove_Side_Panel.png

  12. Choose the best placement for the camera before sticking it on the windshield, but do not attach it yet.

    RHI_Dashcam_Mounting_Position.png

  13. Adjust the road facing camera angle so it is evenly centered on the horizon.

    RHI_Daschcam_Adjust_Road_Facing_Camera.png

  14. If the unit has a driver-facing camera, complete the same steps of aligning the camera so both headrests are in full view.

    RHI_Dashcam_Adjust_Driver_Facing_Camera.png

  15. Clean the windshield using the alcohol wipes provided. Ensure that it is thoroughly dried.

    RHI_Dashcam_Clean_Windshield.png

  16. Mount the camera and bracket, and hold firmly for 30 seconds.

    RHI_Dashcam_Mount_Camera.png
  17. Remove the road-facing camera from the bracket.

  18. Lock the road-facing camera in position.

    RHI_Dashcam_Lock_Road_Facing_Camera.png

  19. If the unit has a driver-facing camera, lock it into position.

    RHI_Dashcam_Lock_Driver_Facing_Camera.png

  20. Tuck the cables into the roof lining and down the A-pillar using the tools and supplies provided.

    RHI_Dashcam_Tidy_Cables.png

  21. Place the privacy covers in the drawstring bag provided.

    Note

    Make sure that it's easily accessible/visible to driver - like a cup holder or driver side door panel.

    RHI_Dashcam_Store_Privacy_Covers.png

  22. A temporary loading screen will show while the camera pairing takes place, then a confirmation once completed.

    RHI_Dashcam_Assign_Camera.png

  23. To view alignment, select Check preview.

    RHI_Dashcam_Check_Preview.png

  24. Select Check preview to view the camera alignment.

    RHI_Dashcam_Preview_Road_Camera.png

  25. If a driver-facing camera is installed, select Next camera to view its alignment.

    RHI_Dashcam_Preview_Driver_Camera.png
  26. Select Close on the top right when completed.

  27. Review installation details, and select CHECK IN to complete.

    RHI_Dashcam_Check_In.png

Next: Replacing a 3G vehicle tracker with a VDD .

Was this article helpful?

0 out of 0 found this helpful